APPLICATIONS AND IMPLICATIONS
WEEK 17
Task:
propose a final project that integrates the range of units covered
what will it do?
The issue of the project consist in make a interactive sculpture, that react when people pass their hands on the top of the module, each module has a led, photoresistor and servomotor.
who's done what beforehand?
- Five years ago in different college in Europe
- Master degree programs
- MIT
S.O.I.L. from soilarchitecture on Vimeo.
what materials and components will be required?
Manufacturing:
- Acrylic of 4mm 30 x 60cm
- MDF of 4mm
- Screw
Electronics:
- Jumper wires
- Servo motor
- Photoresistor(LDR)
- Protoboard
- Fabduino (ATmega 328)
- LEDS
- Resistor 20 ohm
- Resistor 10K
where will they come from?
Manufacturing:
- Acrylic of 4mm 30 x 60cm: Fab Lab inventory
- MDF of 4mm: Fab Lab inventory
- Screw: Fab Lab inventory
Electronics:
- Jumper wires: Local Supplier
- Servo motor: Local supplier
- Photoresistor(LDR): Local Supplier
- LEDS: Local Supplier
- Resistor 220 ohm: Local Supplier
- Resistor 10K: Local Supplier
- Protoboard: made by my self
- Fabduino (ATmega 328): made by my self with Fab Lab inventory
how much will it cost?
Unit
Item
Supplier
Price
06
02
48
08
16
16
16
16
16
8
1
4
4
16
4
4
Acrylic of 4mm
MDF of 4mm
Screw
ServoMotor
Photoresistor
Leds
Resistor 10 K
PROTOBOARD
Pin header 1x40
Board
4 Fabduino
ATmega 328
Led1006 SMD
Pin header 1x6
Switch 6mm
Resonator 8 mhz
Fab lab inventory
Fab lab ineventory
Fab Lab inventory
Singapur Electronics
Electrotec
Electronica Hi-Fi
Singapur Electronics
Singapur Electronics
Electronica Hi-Fi
Singapur Electronics
Fab Lab inventory
Fab Lab inventory
Fab Lab inventory
Fab Lab inventory
Fab Lab inventory
Jumper wires
$22.0
$3.00
$14.5
$46.0
$2.40
$2.50
$3.00
$3.00
$2.50
$1.00
$4.80
$2.40
$0.28
$0.36
$0.28
$0.78
$2.64
$1.20
$0.83
Electronica Hi-Fi
Resistor 220 ohm
Fab Lab inventory
Fab Lab inventory
Fab Lab inventory
Fab Lab inventory
8
Capacitor .1 uf
4
Capacitor 10 uf
4
Resistor 10k
4
Resistor 499
Total
$88.47
what parts and systems will be made?
- Pieces of acrylic
- Protoboard
- Fabduino
- Program codes
what processes will be used?
- Laser cut
- Wires soldering
- Board soldering
- Programming
what tasks need to be completed?
- Design module of acrylics witch laser cut
- Desgin board and protoboard for connect the signal
- Programming code for read LDR, LEDs and servomotors
what questions need to be answered?
- How to assembly each module?
- How to write the programming for read digital signal?
- How to write the programming for read analog signal?
- How to wire all the components?
what is the schedule?
- 08/07 Design and test the prototype
- 15/07 Program the sensors and outputs(servo motor)
- 22/07 Assembly and wire all the components
How will it be evaluated?
Reading servo motor signal
Reading photoresitor signal
Operation of the mechanism
Turn on Leds according the signal
what will it do?
who's done what beforehand?
what materials and components will be required?
where will they come from?
how much will it cost?
what parts and systems will be made?
what processes will be used?
what tasks need to be completed?
what questions need to be answered?
what is the schedule?
how will it be evaluated?
projects can be separate or joint, but need to show individual mastery of all of the skills
where possible, you should make rather than buy the parts of your project
Copyright © Jorge Huang Li - FAB ACADEMY 2016